1-16 of 257 results for "flocking spray" Prextex Christmas Artificial Snow Spray Pack of Two 13 Oz Aerosol Decoration Tree Holiday Winter Fake Crafts Winter Party Snow Santa Snow Nieve (13 OZ) 4.2 out of 5 stars 394. Flock It! Contains antioxidants that prevent hair damage and protect from color fading. J ust what is floc king? Apply to wet hair for easier and faster styling. This should be done before the fibers are applied. How do I use it: Shake well, then apply to dry hair. In the case of my lion the skin colour below the fur was mainly black. Some care should be taken in handling at this time. Hair punching is the process of embedding hair into the surface of a prop using needle called a punching tool.
Flocking is the application of millions of tiny fibers onto an adhesive coated surface to create a velvet-like texture. The undercoat adhesive remains open to the fibers for 10 to 15 minutes—this is your working time. Remember, you should wear a dusk mask, do not skimp on the adhesive (any oil base or paint in the color you are flocking will work except spray paint), don’t skimp on the fibers, and resist the temptation to touch the surface before the finish has dried. Flocking is the process of electrostatically charging small strands of fibre with a high voltage electric field then depositing them into the adhesive coated surface. You CANNOT overcoat—only so much will stick. If you cover the uncoated section(s) with a piece of cardboard and then move the cardboard as needed, you will not have to wait for each compartment to dry before applying the fibers to the next section(s). Flocking is the process of electrostatically charging small strands of fibre with a high voltage electric field then depositing them into the adhesive coated surface. If you are working on a project that has many small sections (compartments), requiring a more detailed application, finish a few at a time. Fill the applicator up to ½ with flocking fibers, this will allow space for the air to circulate the fibers within the applicator. $28) can come to the rescue. Another is on a Christmas Trees, which may be flocked with a fluffy white spray to simulate snow. Spraying 10" to 12" from your scalp, cover over and underneath all of your hair. Sealing /may be done with lacquer, shellac, sanding sealer, polyurethane, etc.—anything that will prevent the surface from soaking up the adhesive. The white details around areas like the eyes and nostrils were also enhanced by addition white paint. As mentioned above blending colours can be tricky, as the fibres are very difficult to control and I decided some blending in and dulling down was needed. I used Copydex as my adhesive. When the glue dries you are left with a textured surface similar to grass or fur. Flock material is attracted to the earth and flies vertically into the glue. FREE Shipping. This also helps to remove excess hair between shades of flock. It is not necessary to mask areas of your project that will not be coated if the surface is sealed and IF YOU BRUSH CAREFULLY. (Metal, glass and most plastics do not require sealing, but may need a sanding to rough up the surface.) For additional texture and volume, work the product through your hair, scrunching with your fingers as you spray. 35. The following video demonstrates the concept far better than me and I found it really helpful. Even surfaces that appear solid can be porous (e.g. Be cautious when later handling the prop as the flock it is easily damaged.
If the sealer leaves a very slick finish, rough it up slightly with sandpaper. Flock applicators can be very expensive so I made my own flock applicator for less than £10 using a Tupperware box, and some components off eBay. Whilst the primer is drying ensure you have a selection of colour reference material prepared. Excess fibers may be reclaimed and reused. I had a moment of madness and decided to splash out on a fancy airbrush- but a cheap 20-pound airbrush off the net would be sufficient. When your hair is hanging on by a thread — literally — Original Mineral Atonic Spritz (appx. HINT: When coating boxes it is best to spray the fibers on the bottom first, and then spray the sides. https://www.youtube.com/watch?v=6LpzIOP6qRI It can be difficult obtain hair punching tools so I made my own by modifying a conventional sewing needle and a home-made handle- here is a video of how to do so: https://www.youtube.com/watch?v=6F5Q6rUp0IE
This coat of adhesive should be smooth and not dripping wet.
A flocking applicator gives the "flock” negative charge whilst the glue-covered surface is earthed.
I worked into the face with an airbrush set to a very fine controlled spray- too much flow will result in droplets of paint forming on the fur surface. The paint can be mixed with the primer to aid the adhesion- but ensure you clean your airbrush thoroughly after use.
I used this online tutorial as a guideline: http://csxdixieline.blogspot.co.uk/2010/06/howto-static-grass-applicator.html Commonly creature makers paint with the contours of their object to accentuate areas of relief and offer a more expressive result. Flock material is attracted to the earth and flies vertically into the glue. With the flocking applicator filled approx. Some special effects makers suggest using 'pros-aid' instead.
A flocking applicator gives the "flock” negative charge whilst the glue-covered surface is earthed. If the adhesive is absorbed, the fibers will have nothing to adhere to and the finish will have thin spots.